AD-SERVO SERIES
GENERAL INFORMATION
Choose the DURMA AD-Servo series eco-friendly press brake for clean energy saving operations. The AD-Servo is low cost, energy efficient, accurate, speed and quiet.
AD-SERVO Series Press Brakes are specifically designed to increase your productivity and contribute to your precise part bending. Energy consumption has an important place and impact on every business. While energy consumption in standard machines constitutes 30% of the production cost, AD-Servo series press brakes offer low energy consumption.
-
Y1, Y2, X, R – 4-axes
-
Control unit – CNC Cybelec ModEva 10S 3D with PC 1200 3D SW or Delem 66W
-
CNC controlled motorised crowning
-
CNC controlled Hyd-Mech crowning (standard – 800 t)
-
European Clamping system (standard – 400 t)
-
DURMA Clamping system (standard – 600 t)
-
Sliding front arms with full length linear guide
-
Back gauge , Servo-motorised & linear guide & ball bearing system (X- R)
-
Sliding sheet support Arms with T-canal and tilting stop
-
Protection covers
-
Special designed – worldclass hydraulics blocks & valves
-
Worldclass electronics system
OVERVIEW
-
Increase your competitive forces by 62% lower power consumption
-
Lower cost per part by ecological technology
-
Quiet, energy efficient and accurate
-
Ram movement is powered by AC servo motors driving hydraulic oil in line with variable speed pump. New technology allows : Silent bends, noise level reduced to 63 dbA from 76 dbA, energy savings, 62% at stand-by.
-
44% during the press cycle
-
60% in 1 hour with 15 press cycles
-
Supports your production cost efficiency and increases your competitive forces.
-
Small hydraulic oil tank for clean environment & cost reduction
-
Thanks to the new technology reduce hydraulic tank from 200 lt to 2×40 lt
-
Speeds & accuracy & syncronisation
-
Beam speeds to 200mm/sec
-
5,6 times better synchronisation in phase of “high speed“
OTHER FEATURES
Syncro Y1Y2 Axes & CNC Control
- Motorised crowning
- Independent left and right axes (Y1Y2) controlled by electronics servo valves & electronics linear position controllers.
- CNC controlled motorised crowning system homogenises bending forces on ever point of the bending parts The need for shimming is eliminated
Sliding front arms
Quickset support arms are mounted on a linear quide way and ball bearing system that allows “finger tip” lateral adjustment of the front support arms. Vertically adjustment is also easily achieved
X-R Back gauge
Fingers` depth and height is calculated by a CNC controller and executes high speed servo motors produced by Siemens. Retraction is also a standard feature to acquire accurate parts. Back gauge fingers are easily adjusted on linear guides by ball integrated motion system
High Stroke / Daylight / Throat = High working space
AD-S machines offer wide spaces for ease of operation also reduces cycle times
TOOL SYSTEMS
Eurostyle clamping
Eurostyle tool holders offers precise tool setup by their ground surfaces
Eurostyle clamping
Quick release clamping
Hydraulic eurostyle clamping
Hydraulic new standard clamping
Durma tool clamping
Durma hydraulic clamping
OPTIONAL FEATURES
- CE with FIESSLER AKAS-LC II F manual + AKFR control box
- CE with FIESSLER AKAS-LC II AKAS-3 M motorised + FPSC (SAFETY PLC)
- CE with SICK C 4000- only for tandem
- DFS1 laser finger protection ( for Bottom Beam-Non CE )
- Z1, Z2 axes
- X1, X2 axes
- R1, R2 axes
- R1 R2 axes on the finger blocks
- Delta X axis ,+250mm stroke
- X Axis =1000 mm – Back protection with light barrier
- X1 X2 axes = 1250 mm – for lighting pole
- X1 X2 axes = 1250 mm – for lighting pole – pneumatic pushers
- AP3-AP4 sheet follower with sliding guide- motorised height adj
- F1-F2 front feeding system with supports
- F1-F2 front feeding system with supports – pneumatic pushers
- Quick release clamping
- Durma hydraulic or mechanical clamping
- Wila hydraulic or mechanical clamping
- Tool options (Durma, European, Wila) in tool catalogue
- Bottom tool separation system
- Crowning vertical
BACK GAUGE OPTIONS
X, R, Z1, Z2 4 axes
X1, X2, R, Z1, Z2, 5 axes
X1, X2, R1, R2, Z1, Z2, 6 axes
Delta X
BACK GAUGE FINGERS
3 Steps finger blocks
Special fingers
BOTTOM TOOL POSITIONING SYSTEMS
Laser angle measurement system
- Any bending angle can be measured
- Very compact, everything in the appliance
- Light influence, light or dark material surfaces play practically no part at all
Pneumatic positioning system
Motorised positioning system
CNC CONTROL UNIT
Controller- DELEM DA-66T
– Touchscreen
– 17″ display
– Easy to operate
– Full Windows application suit
– 2D graphical showing operator when to flip or turn the product.
– Create profiles with finger draw.
– Punch and die memory
Controller- DELEM DA-69T
– Touchscreen
– 17″ display
– Easy to operate
– Full Windows application suit
– 2D graphical showing operator when to flip or turn the product.
– Create profiles with finger draw.
– Punch and die memory
DELEM Profile-T3D offline software
– 3D programming version
– 3D machine representation
– X1-X2 angle programming
– 3D finger view
– DA-Touch familiar user interface
– DXF import function
DATA SHEET
