– RP SERIES ROTATIONAL – HEAD PUNCH
GENERAL INFORMATION
Versatile ‘C’ frame construction with an indexible multi tool punch station.
-
Command pedal
-
CAD-CAM software & Activator
-
Control unit, Siemens Sinumerik 840 D SL Windows XP operating system
-
Remote diagnostic function
-
Programming on the control panel
-
Automatic clamp positioning (RP9)
-
Sheet set switches on clamps (RP9)
-
Network, Ethernet communication.
-
standart 6multi tool with punch and dies
-
6 pieces Durma tool and guide( gap 0.3 mm ) – round Ø8/round Ø10/round Ø20/rectangle 4 x 20/square 7/square 17
-
Automatic tool lubrication
-
Alignment Tools for Index Stations (D Station)
-
Movable scrap box
-
UPS for control panel
-
USB driver
-
Brush table
-
Control panel
-
Oil Cooler
-
Reposition on X axis
-
Web cam for service
-
Manual nesting
FEATURES
Siemens Controller
Durma has chosen the very powerful Siemens 840 DsI CNC Control, which has been specially designed for punching. Some of the features are:
■ Movable Control Cabinet
■ Ethernet and Network Connections
■ Internal Diagnostics
■ Online Help Messages
■ Automatic Optimization of Sheet Speed According to Sheet Mass
■ Graphic Programming @ Machine Control
■ Sheet Layout & Automatic Calculation of Sheet Layout
■ Removable Software Key (office or machine programming)
Software
CAD/CAM software features:
■ Automatic Contour Check and Correction
■ Automatic Punching
■ Supports Wire-Joints and Micro-Joints
■ Allows Predefined Shapes Placement
■ Full Common Cut Support
■ Turret Setup Customization
■ Sheet Reposition and Transformation
■ Auto-Indexing
■ Offers Special Tools Support
■ Automatic and Manual Clamp Avoidance
Multi Tool
Durma rotation punch press machines can angular position each tool station within ± 0,02°. Upper and lower tools have no mechanical connection which means they can be perfectly aligned, even defects in the tools can be adjusted out. Standard is the 6 tool station you can option 3, 6, 8 or 10 tool stations
Rotational Head
The full 360° programmable head achieves 40 revolution per minute. A harmonic zero backlash gear driven system provides accurate positioning and control.
Intelligent High-Speed Hydraulics
DURMA uses a Bosch – Rexroth advanced closed loop hydraulic system. Being a closed loop system allows forming and the use of Wilson’s “wheel” technology.
Programmable Sheet Clamps & Auto Sheet Re-positioning
The position of the sheet clamps are automatically set by standard program information. Contact sensors automatically stop the machine if these sensors detect any movement of the sheet while it is clamped.
Siemens AC Servo Direct Drive System
SIEMENS AC Servo Direct Drive System
A new design direct drive positioning system for the X and Y axis increases performance and eliminates any
efficiency loss due to belts, gears, and transmissions. Both axis are driven by Siemens servo motors. Simultaneous positioning speeds of 120 m/min are reached. 1g acceleration is achieved over the whole working range
OPTIONAL FEATURES
- Light barriers for CE
- Additional clamps
- Special table
- Tools, Tool holders, reducers
- CAD-CAM SW Second activator (dongle)
- SW for Autonesting & Wheel tools
- Additional table
- Air condition for electrical box
- Additional oil cooler
- Warning lamp
- Sheet deformation alert switch
- Workchute for RP9
- Automatic lubrication for the machine
- UPS for machine ( 30KvA – 10 min )
- Transformator
- Auto Nesting and wheel soft
[pdf-embedder url = “https://cptb0tiy.dreamwp.com/wp-content/uploads/2021/06/Durma_TurretPunch_RP.pdf”]